...
| Table of Contents |
|---|
Network Requirement
...
Figure 1. BGP Load Balancing
Procedure
This section describes the steps of how to configure basic BGP functions on SwitchA, SwitchB, SwitchC and SwitchD.
Switch A
Step1 Configure the VLANs and VLAN interfaces.
...
| Code Block |
|---|
admin@SwitchA# set protocols bgp router-id 1.1.1.1 admin@SwitchA# set protocols bgp local-as 100 admin@SwitchA# set protocols bgp neighbor 192.168.30.2 remote-as 200 admin@SwitchA# set protocols bgp neighbor 192.168.40.2 remote-as 300-as 300 admin@SwitchA# set protocols bgp ebgp-requires-policy false |
Step3 Enable IP routing.
...
| Code Block |
|---|
admin@SwitchB# set protocols bgp router-id 2.2.2.2
admin@SwitchB# set protocols bgp local-as 200
admin@SwitchB# set protocols bgp neighbor 192.168.30.1 remote-as 100
admin@SwitchB# set protocols bgp neighbor 192.168.20.1 remote-as 400
admin@SwitchB# set protocols bgp ebgp-requires-policy false |
Step3 Enable IP routing.
...
| Code Block |
|---|
admin@SwitchC# set vlans vlan-id 40 l3-interface 40vlan40 admin@SwitchC# set vlans vlan-id 50 l3-interface 50vlan50 admin@SwitchC# set interface gigabit-ethernet te-1/1/2 family ethernet-switching native-vlan-id 40 admin@SwitchC# set interface gigabit-ethernet te-1/1/3 family ethernet-switching native-vlan-id 50 admin@SwitchC# set l3-interface vlan-interface vlan40 address 192.168.40.2 prefix-length 24 admin@SwitchC# set l3-interface vlan-interface vlan50 address 192.168.50.2 prefix-length 24 |
...
| Code Block |
|---|
admin@SwitchC# set protocols bgp router-id 3.3.3.3
admin@SwitchC# set protocols bgp local-as 300
admin@SwitchC# set protocols bgp neighbor 192.168.40.1 remote-as 100
admin@SwitchC# set protocols bgp neighbor 192.168.50.1 remote-as 400
admin@SwitchB# set protocols bgp ebgp-requires-policy false |
Step3 Enable IP routing.
...
| Code Block |
|---|
admin@SwitchD# set protocols bgp router-id 4.4.4.4
admin@SwitchD# set protocols bgp local-as 400
admin@SwitchD# set protocols bgp neighbor 192.168.20.2 remote-as 200
admin@SwitchD# set protocols bgp neighbor 192.168.50.2 remote-as 300
admin@SwitchD# set protocols bgp ebgp-requires-policy false |
Step3 Enable IP routing.
...
| Code Block |
|---|
admin@SwitchD# commit |
Viewing BGP Peer Status on Switch B
...
| Code Block |
|---|
admin@SwitchB# run show bgp neighbor
BGP neighbor on vlan30: 192.168.30.1, remote AS 100, local AS 200, external link
BGP version 4, remote router ID 1.1.1.1, local router ID 2.2.2.2
BGP state = Idle
Last read 00:15:06, Last write never
Hold time is 180, keepalive interval is 60 seconds
Graceful restart information:
Local GR Mode: Helper*
Remote GR Mode: NotApplicable
R bit: False
Timers:
Configured Restart Time(sec): 120
Received Restart Time(sec): 0
Message statistics:
Inq depth is 0
Outq depth is 0
Sent Rcvd
Opens: 0 0
Notifications: 0 0
Updates: 0 0
Keepalives: 0 0
Route Refresh: 0 0
Capability: 0 0
Total: 0 0
Minimum time between advertisement runs is 0 seconds
For address family: IPv4 Unicast
Not part of any update group
Community attribute sent to this neighbor(all)
0 accepted prefixes
Connections established 0; dropped 0
Last reset 00:15:06, Waiting for Peer IPv6 LLA
BGP Connect Retry Timer in Seconds: 120
Read thread: off Write thread: off FD used: -1
BGP neighbor is 192.168.20.2, remote AS 400, local AS 200, internal link
Administratively shut down
BGP version 4, remote router ID 3.3.3.3, local router ID 2.2.2.2
BGP state = Idle
Last read 00:15:06, Last write never
Hold time is 180, keepalive interval is 60 seconds
Graceful restart information:
Local GR Mode: Helper*
Remote GR Mode: NotApplicable
R bit: False
Timers:
Configured Restart Time(sec): 120
Received Restart Time(sec): 0
Message statistics:
Inq depth is 0
Outq depth is 0
Sent Rcvd
Opens: 0 0
Notifications: 0 0
Updates: 0 0
Keepalives: 0 0
Route Refresh: 0 0
Capability: 0 0
Total: 0 0
Minimum time between advertisement runs is 600 seconds
For address family: IPv4 Unicast
Not part of any update group
Advertise bestpath per AS via addpath
Override ASNs in outbound updates if aspath equals remote-as
Community attribute sent to this neighbor(all)
0 accepted prefixes
Connections established 0; dropped 0
Last reset 00:15:06, No AFI/SAFI activated for peer
External BGP neighbor may be up to 255 hops away.
BGP Connect Retry Timer in Seconds: 111
Peer Authentication Enabled
Read thread: off Write thread: off FD used: -1
BGP neighbor is 192.168.40.2, remote AS 200, local AS 200, internal link
BGP version 4, remote router ID 4.4.4.4, local router ID 2.2.2.2
BGP state = Active
Last read 00:15:06, Last write never
Hold time is 180, keepalive interval is 60 seconds
Graceful restart information:
Local GR Mode: Helper*
Remote GR Mode: NotApplicable
R bit: False
Timers:
Configured Restart Time(sec): 120
Received Restart Time(sec): 0
Message statistics:
Inq depth is 0
Outq depth is 0
Sent Rcvd
Opens: 0 0
Notifications: 0 0
Updates: 0 0
Keepalives: 0 0
Route Refresh: 0 0
Capability: 0 0
Total: 0 0
Minimum time between advertisement runs is 0 seconds
For address family: IPv4 Unicast
Not part of any update group
Advertise bestpath per AS via addpath
Override ASNs in outbound updates if aspath equals remote-as
Community attribute sent to this neighbor(all)
0 accepted prefixes
Connections established 0; dropped 0
Last reset 00:15:06, No AFI/SAFI activated for peer
External BGP neighbor may be up to 255 hops away.
BGP Connect Retry Timer in Seconds: 111
Peer Authentication Enabled
Read thread: off Write thread: off FD used: -1 |
...
| Code Block |
|---|
admin@SwitchA# set protocols bgp ipv4-unicast multipath ibgpebgp maximum-paths 2 admin@SwitchA# commit |
...