| Table of Contents |
|---|
...
- If you want to install PICOS through a console port, refer to sections Traditional Installation or Nos-boot-mode Installation.
- If you want to install the PICOS through a non-console port (through the management port), refer to section Nos-boot-mode Installation.
| Warning |
|---|
• You need to log in through the console port of the switch and perform the ONIE installation. • Other NOSes including user data will be removed when install PICOS under ONIE environment. • When the ONIE installer is used to downgrade the PICOS version from version 4.x to PICOS 3.x or lower versions, we first need to use ONIE to uninstall the higher version PICOS before proceeding with installing PICOS 3.x or a lower version. On the ARM platform, execute the onie_uninstaller command at the ONIE prompt to uninstall the current version PICOS. On the x86 platform, select the "ONIE: Uninstall OS" option in the GRUB menu to uninstall the current version PICOS. • If you enter GRUB rescue mode and the switch has GPT format partition, you can use the following commands to reset the GRUB boot variable to enter ONIE GRUB and then install PICOS. grub rescue> set prefix=(hd0,gpt2)/grub • Do not plug in the USB disk during onie-nos-installer process until ONIE starts up. If you have plugged in the USB disk before the installation operation, ONIE will find the installer on the USB disk when beginning the installation. On AS4610 series switches, when installation is complete, the installer will display: Please take out the usb disc, then remove the USB disk within 10 seconds after installation successful, and before machine restarts. • All X86 platforms share one installation and upgrade package with the name fixed as: onie-installer-picos-VERSION-x86.bin, where VERSION is the release version. X86 platform are listed below: • FS N5850-48S6Q • FS N8550-48B8C • FS N8550-32C • Edgecore AS4630-54PE • Edgecore AS5835-54X • DELL N3248P-ON • DELL S5212F-ON • DELL S5248F-ON • DELL Z9100-ON • DELL Z9264F-ON • DELL N3224T-ON • DELL S4128T-ON |
...
NOTE：
|
Mind Map of Installation Process
Figure1 shows the mind map of PICOS installation process.
...
Step2 Enter ONIE installation environment. The process is different on the following two types of platforms:
ARM Platforms (AS4610 Series Switches)Anchor p1 p1
...
Step2 Install PICOS via ONIE. The process is different on the following two types of platforms:
ARM Platforms (AS4610 Series Switches)Anchor p2 p2
...
The installation methods described in Traditional Installation must be performed through the console port. If you want to install the system through a non-console port, you can use the nos-boot-mode command to perform the installation which is described in this section.
Usage of nos-boot-mode command: admin@Xorplus$sudo nos-boot-mode USAGE install or uninstall NOS(es) SYNOPSIS nos-boot-mode [install|uninstall] DESCRIPTION install- Install NOS uninstall- Remove all NOS(es) including PICOS When nos-boot-mode install command is executed, PICOS will switch to ONIE install mode, and the user should go on to complete the subsequent installation. The steps for the manual installation process and the automatic installation process using the nos-boot-mode install command are described below. When nos-boot-mode unsinstall command is executed, the system will remove all NOS(es) including PICOS from the device. Therefore, it is suggested to use the nos-boot-mode unsinstall command with caution. |
Manual Installation Process
Step1 Make sure that the installation package of .bin file has been loaded to the server (server could be HTTP, TFTP, or an FTP server or the switch local directory depending on the actual installation environment).
...