Versions Compared

Version Old Version 4 New Version Current
Changes made by

Tracy Yang

Tracy Yang

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  •  Configure a static route for each VRF for data forwarding. For example, the destination network segment is 10.10.1.0/24, the next hop is 172.168.1.13.

Procedure

Step1         Enable IP routing function before using VRF function.

...

Step5         (Optional) Configure a static route entry into the VRF, the destination network segment is 10.10 1.0/24, the next hop is 172.168.1.13.

Code Block
admin@XorPlus# set protocols static vrf vrf1 route 10.10.1.0/24 next-hop 172.168.1.3
admin@XorPlus# set protocols static vrf vrf2 route 10.10.1.0/24 next-hop 172.168.1.3

...

  • You can use the run show route vrf command to check the routing table information of the specific VRF.
Code Block
admin@Xorplus#admin@XorPlus# run show route vrf vrf1
show ip route vrf vrf1 
=======================
Codes: K - kernel route, C - connected, S - static, R - RIP,
       O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
       T - Table, v - VNC, V - VNC-Direct, A - Babel, DF - SHARPPBR,

      F - PBR, f - OpenFabric,
       > - selected route, * - FIB route, q - queued route, r - rejected route
, b - backup
       t - trapped, o - offload failure

VRF vrf1:
K>S>* 17210.16810.1.10/3224 [2551/81920] unreachable (ICMP unreachable), 04:31:56
K>via 172.168.1.3, vlan10, weight 1, 00:00:45
C>* 172.168.1.0/24 [2400/8192] unreachable (ICMP unreachable), 04:31:56


show ipv6 is directly connected, vlan10, 00:04:43
C>* 192.168.2.0/24 is directly connected, vlan11, 00:04:45

admin@XorPlus# run show route vrf vrf2
show ip route vrf vrf1vrf2 
=========================

  • You can use the run show route forward-host command to check the information about the host hardware forwarding table information of the specific VRF, run show route forward-route command to check the hardware route forwarding table information of the specific VRF.

Code Block
admin@XorPlus# run show route vrf vrf1 forward-route ipv4 all
Destination      NextHopMac    
Codes: K - kernel route, C - connected, S - static, R - RIP,
       O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
    Port   T - Table, v - VNC, V - VNC-Direct, A - Babel, F ------ PBR,
       f - OpenFabric,
       > - selected route, * - FIB route, q - queued, r - rejected, b - backup
       t ------------   --------- trapped, o - offload failure

VRF vrf2:
S>* 10.10.1.0/24 [1/0] via 172.168.1.3, vlan20, weight 1, 00:00:59
C>* 172.168.1.0/24 is directly connected, vlan20, 00:04:7D:7B:62:93:FF   connected

Total route count:1
Code Block
admin@Xorplus#56
C>* 192.168.2.0/24 is directly connected, vlan21, 00:04:59
  • You can use the run show route forward-route command to check the hardware route forwarding table information of the specific VRF.
Code Block
admin@XorPlus# run show route vrf vrf1 forward-hostroute ipv4 all
Address       Destination          NextHopMac          HWaddress     Port       Port   
---------------        -----------------      ---------
192.168.2.0/24       CC:37:AB:BE:0E:D1   connected
172.168.1.0/24       CC:37:AB:BE:0E:D1   connected
10.10.1.1  0/24         04:7D:7B:62:93:FF     te-1/1/3    
Total host count:1  3