NOTE:

Due to ASIC limitation, there are some 100GE interfaces on certain platforms do not support port splitting. For details, see Limitation of Port Breakout.

Introduction

Part of the 400GE, 100GE and 40GE optical interfaces on Pica8 switch can be used as a single interface or split into four independent interfaces. The 40GE interface can be split into four independent and logical 10 Gigabit Ethernet interfaces. The 100GE interface can be split into four independent and logical 25 Gigabit Ethernet interfaces or four 10 Gigabit Ethernet interfaces.The 400GE interface can be split into four 100 Gigabit Ethernet interfaces.

After a single interface is split into Gigabit Ethernet interfaces, the 10GE optical interfaces or the 25GE optical interfaces supports the same configurations and features as other non-breakout optical interface except that the interface is named in a different way. If the port name of the optical interface is xe-1/1/n before port breakout; however, after port breakout the port name of the four interfaces are xe-1/1/n.1, xe-1/1/n.2, xe-1/1 /n.3 and xe- 1/1/n.4.

You can use set interface gigabit-ethernet <port-name> breakout true command to enable port breakout, use set interface gigabit-ethernet <port-name> breakout false command to merge the four interfaces into one interface.

After the interface is split, you need to use a breakout cable to connect to the device at the other end. For example, as shown in the following figure, a 40GE interface must use a breakout cable to connect to the device at the other end after being split into 4 x 10GE interfaces. If the connected peer interface is also a split 40GE interface, the interfaces on both ends can be plugged into the same type of 40GE optical module and connected by one optical fiber instead of using a breakout cable.

Figure 1. The breakout cable

Configuring Port Breakout and Port Merge

We can configure port breakout for the 40GE, 100GE or 400GE interfaces of the switch, the procedures are described as below.

Step1 Split the port as required.

set interface gigabit-ethernet <port-name> breakout true

NOTE:

When you don’t want to split the port, use set interface gigabit-ethernet <port-name> breakout false command to merge the four interfaces into one interface.
You need to restart or reboot the system to make the setting take effect when performing port breakout or port merge operation.
When performing the port merge operation, before restarting the system, you need to manually delete the configurations of the unavailable interfaces, to make sure that the configuration file can be loaded normally when the system boots up.
The 100GE interface can be split into 4 x 25G or 4 x 10G Ethernet interfaces. By default, the 100G interface is split into 4 x 25G Ethernet interfaces. If you want to split into 4 x 10G Ethernet interfaces, you need to configure the four interfaces rate to 10G through the command line after port breakout. Note: The rate of the four interfaces is required to be consistent.

Step2 Restart PICOS to make the setting take effect.

admin@XorPlus:~$ sudo systemctl restart picos

Step3 Verify the configuration.

For example, we have configured to split the 40GE port xe-1/1/25 into 4 x 10GE ports.

After system startup, run run show interface brief command to view the interface information. After system startup, run run show interface brief command to view the interface information.

admin@XorPlus# set interface gigabit-ethernet xe-1/1/25 breakout true
admin@XorPlus# commit
Commit OK.
Save done.
Interface breakout setting has been changed, please reboot the system for changes to take effect!
Make sure to delete all the configurations associated with the unavailable interfaces, otherwise loading startup configuration will fail.
admin@PICOS> request system reboot
admin@Xorplus> configure
admin@XorPlus# run show interface brief 
Interface   Management  Status  Flow Control  Duplex  Speed    Description
----------  ----------  ------  ------------  ------  -------  ------------------------------
......
xe-1/1/25.1 Enabled     Down    Disabled      Full    10Gb/s     
xe-1/1/25.2 Enabled     Down    Disabled      Full    10Gb/s     
xe-1/1/25.3 Enabled     Up      Disabled      Full    10Gb/s   
xe-1/1/25.4 Enabled     Up      Disabled      Full    10Gb/s   
......

Browser not supported