N3224PX-ON


Front Panel Schematic

(1) Stacking LED

(2) System LED

(3) Power LED

(4) FAN LED

(5) Beacon LED

(6) 7-DIGIT Stack LED

(7) 10G Cu port

(8) 25GbE SFP28

(9) Reset button

(10)  Micro-USB

(11) USB port

(12) Console port

(13) Management Ethernet port

-

 -

Rear Panel Schematic

(1) PSU1

(2) PSU2

(3) FAN1

(4) FAN2

(5)  FAN3

(6) HiGig2 stacking ports (QSFP28)

Switch System Characteristics

Mechanical Dimension

Standard 1U chassis height

Management-ethernet port

1

Console port

1

10G Cu port

24

25GbE SFP28

4

Power LED

1

Stacking LED

1

FAN LED

1

System LED

1

Beacon LED

1

7-DIGIT Stack LED

1

10G Cu port LED

1 x 24

25GbE SFP28 LED

2 x 4

HiGig2 stacking ports (QSFP28)

2

HiGig2 stacking ports (QSFP28) LED

4 x 2

Micro-USB

1

USB port

1

Reset button

1

PSU

2

FAN

3

 

*UPoE

  • The 24 RJ45 ports on the front panel of N3224PX-ON support UPoE. For these UPoE ports, the maximum output power can be set to up to 99 watts. For details about UPoE, please refer to UPoE.
  • See the link PoE Configuration Commands for PoE command reference, the following PoE commands are not supported on N3224PX-ON:

set poe interface max-power

set poe interface mode

set poe interface threshold-mode

set poe power management-mode

 

25GbE SFP28 Port

Ports Te-1/1/25, Te-1/1/26, Te-1/1/27 and Te-1/1/28 are a group of ports, you should manually configure the port speed for these four ports by using the set interface gigabit-ethernet speed command before inserting an optical module. When configuring the rate, the supported port rates are 25 Gbit/s, 10 Gbit/s, and 1 Gbit/s. The four ports can be configured with the same port rate or different rate. When configured at different port rates, 10G and 1G can coexist, but 25G cannot coexist with other rates. The following table gives several cases of speed setting for this group of ports.

 

te-1/1/25

te-1/1/26

te-1/1/27

te-1/1/28

Allowed or not allowed

case #1

10 G

10G

10G

10G

case #2

1G

1G

1G

1G

case #3

25G

25G

25G

25G

case #4

1G

10G

1G

10G

case #5

25G

1G

25G

25G

X

case #6

25G

10G

25G

10G

X

case #7

25G

1G

10G

25G

X

 

Note: If the port rate is set to 25 Gbit/s, but a 10 Gbit/s optical module is inserted, the port cannot go up.

 

HiGig2 stacking ports

N3224PX-ON has one slot for QSFP module at the rear side which can be plugged in 2 x 100G QSFP modules. The port numbers of the QSFP module are x-1/1/1 and xe-1/1/2. They can be used as normal 100G QSFP28 ports.

Copyright © 2024 Pica8 Inc. All Rights Reserved.