N3224P-ON//N3224T-ON
Front Panel Schematic
(1) Stacking LED | (2) System LED | (3) Power LED |
(4) FAN LED | (5) Beacon LED | (6)Â 7-DIGIT Stack LED |
(7) 1G Cu port | (8)Â 10G SFP28 port | (9)Â Reset button |
(10) Micro-USB | (11) USB port | (12)Â Console port |
(13) Management Ethernet port | - | Â - |
Rear Panel Schematic
(1) PSU1 | (2) PSU2 | (3) FAN1 |
(4)Â FAN2 | (5)Â FAN3 | (6)Â HiGig2 stacking ports (QSFP28) |
Switch System Characteristics
Mechanical Dimension | Standard 1U chassis height |
Management-ethernet port | 1 |
Console port | 1 |
1G Cu port | 24 |
10G SFP28 port | 4 |
Power LED | 1 |
Stacking LED | 1 |
FAN LED | 1 |
System LED | 1 |
Beacon LED | 1 |
7-DIGIT Stack LED | 1 |
1G Cu port LED | 1 x 24 |
10G SFP28 port LED | 2 x 4 |
HiGig2 stacking ports (QSFP28) | 2 |
HiGig2 stacking ports (QSFP28) LED | 4 x 2 |
Micro-USB | 1 |
USB port | 1 |
Reset button | 1 |
PSU | 2 |
FAN | 3 |
Â
*PoE
- The 24 RJ45 ports on the front panel of N3224P-ON support PoE but N3224T-ON doesn't support. For these PoE ports, the maximum output power can be set to up to 30 watts.
- See the link PoE Configuration for PoE command reference, the following PoE commands are not supported on N3224P-ON:
set poe interface max-power
set poe interface detection-type
set poe interface mode
set poe interface threshold-mode
set poe power management-mode
25GbE SFP28 Port
Ports Te-1/1/25, Te-1/1/26, Te-1/1/27 and Te-1/1/28 are a group of ports, you should manually configure the port speed for these four ports by using the set interface gigabit-ethernet speed command before inserting an optical module. When configuring the rate, the supported port rates are 25 Gbit/s, 10 Gbit/s, and 1 Gbit/s. The four ports can be configured with the same port rate or different rate. When configured at different port rates, 10G and 1G can coexist, but 25G cannot coexist with other rates. The following table gives several cases of speed setting for this group of ports.
 | te-1/1/25 | te-1/1/26 | te-1/1/27 | te-1/1/28 | Allowed or not allowed |
case #1 | 10 G | 10G | 10G | 10G | ✓ |
case #2 | 1G | 1G | 1G | 1G | ✓ |
case #3 | 25G | 25G | 25G | 25G | ✓ |
case #4 | 1G | 10G | 1G | 10G | ✓ |
case #5 | 25G | 1G | 25G | 25G | X |
case #6 | 25G | 10G | 25G | 10G | X |
case #7 | 25G | 1G | 10G | 25G | X |
Â
Note: If the port rate is set to 25 Gbit/s, but a 10 Gbit/s optical module is inserted, the port cannot go up.
Â
HiGig2 stacking ports
N3224P-ON has one slot for QSFP module at the rear side which can be plugged in 2 x 100G QSFP modules. The port numbers of the QSFP module are x-1/1/1 and xe-1/1/2. They can be used as normal 100G QSFP28 ports.
Copyright © 2024 Pica8 Inc. All Rights Reserved.