show interface gigabit-ethernet <interface>
This command is to show brief,detail or dot1q-tunneling information of a specified port.
Command Syntax
run show interface gigabit-ethernet <interface> [text]
Parameter
•<interfce> a specified interface identifier,[ge-1/1/1...ge-1/1/48],[te-1/1/49...te-1/1/52]
•[text] The special information.
- brief Show interface brief information
- detail Show interface detail information
- dot1q-tunneling Show dot1q tunneling information about the specified interface
Example
• This example is to show detail information on ge-1/1/3:
admin@XorPlus# run show interface gigabit-ethernet ge-1/1/3 detail Physical interface: ge-1/1/3, Enabled, error-discard False, Physical link is Up Interface index: 3, SFP type: Unknown, Mac Learning Enabled Port mode: access Description: Link-level type: Ethernet, MTU: 1514, Speed: 100Mb/s, Duplex: Full Source filtering: Disabled, Flow control: Disabled, Auto-negotiation: Enabled Interface flags: Hardware-Down SNMP-Traps Internal: 0x0 Interface rate limit ingress:0, egress:0 Current address: 08:9e:01:a8:00:49, Hardware address: 08:9e:01:a8:00:49 Traffic statistics: 5 sec input rate 0 bits/sec, 0 packets/sec 5 sec output rate 392 bits/sec, 0 packets/sec Input Packets............................10000 Output Packets...........................186601 Input Octets.............................640000 Output Octets............................15763131 Transmit: Unicast packets........................91800 Multicast packets......................64781 Broadcast packets......................30020 Packets 64 Octets......................121822 Packets 65-127 Octets..................64777 Packets 128-255 Octets.................2 Packets 256-511 Octets.................0 Packets 512-1023 Octets................0 Packets 1024-1518 Octets...............0 Oversize Packets.......................0 Total Packets Without Errors...........186601 Discarded Packets......................0 Total Packets With Errors..............0 Single Collision Frames................0 Multiple Collision Frames..............0 Deferred Frames........................0 Late Collisions........................0 Excessive Collisions...................0 Pause Frames...........................0 Receive: Unicast packets........................10000 Multicast packets......................0 Broadcast packets......................0 Packets 64 Octets......................10000 Packets 65-127 Octets..................0 Packets 128-255 Octets.................0 Packets 256-511 Octets.................0 Packets 512-1023 Octets................0 Packets 1024-1518 Octets...............0 Oversize Packets.......................0 Total Packets Without Errors...........10000 Discarded Packets......................0 Total Packets With Errors..............0 Alignment Errors.......................0 FCS Errors.............................0 Collisions.............................0 Pause Frames...........................0 admin@Xorplus# run show interface gigabit-ethernet te-1/1/1 Physical interface: te-1/1/1(49), Enabled, error-discard False, Physical link is Up Interface index: 49, SFP+ type: 10G_BASE_SR, Mac Learning Enabled Description: Link-level type: Ethernet, MTU: 1518, Speed: 10Gb/s, Duplex: Full Source filtering: Disabled, Flow control: Disabled Auto-negotiation: Disabled Interface flags: SNMP-Traps Internal: 0x0 Interface rate limit ingress:unlimited, egress:unlimited Interface burst limit ingress:unlimited, egress:unlimited Link fault signaling ignore local fault:false, ignore remote fault:false force up mode:true Precision Time Protocol mode:none Current address: 1c:72:1d:c9:1b:e1, Hardware address: 1c:72:1d:c9:1b:e1 Traffic statistics: 5 sec input rate 0 bits/sec, 0 packets/sec 5 sec output rate 1607765248 bits/sec, 2450861 packets/sec Input Packets............................0 Output Packets...........................17156180968 Input Octets.............................0 Output Octets............................1406807017424
Copyright © 2024 Pica8 Inc. All Rights Reserved.