Example for Configuring IPv4 Static Routes
Unicast routing involves sending data from a single sender to a single receiver, making it a point-to-point routing protocol. Examples of unicast protocols include TCP and HTTP. Various forms of Layer 3 routing are considered unicast, including static routing. Static routing is used to manually configure a routing entry rather than rely on dynamic routing. As the name implies, static routes are fixed routes that do not change. They may be used as a backup to dynamic routing, to ensure a valid path exists between two points.
This document describes an example of how to configure a static route between two hosts in a network using open white box switches running the Pica8 PICOS network operating system.
Configuration Example
An example of configuration with static routing is shown in Fig. 5-1. Host A and Host B should be able to communicate with each other. Host A and Host B should be able to communicate with the gateway (e.g., access Internet).
                  Figure 5-1. Static routing configuration.Â
Configuring Switch A
For Switch A, configure 3 VLAN interfaces for networks 10.10.1.1/24, 10.10.3.1/24, and 10.10.6.1/24. Also configure a static route to 10.10.2.0/24 and a default route.
admin@XorPlus# set vlans vlan-id 2 admin@XorPlus# set vlans vlan-id 3 admin@XorPlus# set vlans vlan-id 4 admin@XorPlus# set interface gigabit-ethernet ge-1/1/1 family ethernet-switching native-vlan-id 2 admin@XorPlus# set interface gigabit-ethernet ge-1/1/2 family ethernet-switching native-vlan-id 3 admin@XorPlus# set interface gigabit-ethernet ge-1/1/3 family ethernet-switching native-vlan-id 4 admin@XorPlus# set vlans vlan-id 2 l3-interface vlan-2 admin@XorPlus# set vlans vlan-id 3 l3-interface vlan-3 admin@XorPlus# set vlans vlan-id 4 l3-interface vlan-4 admin@XorPlus# commit Commit OK. Save done. admin@XorPlus# set l3-interface vlan-interface vlan-2 address 10.10.1.1 prefix-length 24 admin@XorPlus# set l3-interface vlan-interface vlan-3 address 10.10.3.1 prefix-length 24 admin@XorPlus# set l3-interface vlan-interface vlan-4 address 10.10.6.1 prefix-length 24 admin@XorPlus# set ip routing enable true admin@XorPlus# set protocols static route 10.10.2.0/24 next-hop 10.10.6.2 admin@XorPlus# set protocols static route 0.0.0.0/0 next-hop 10.10.3.2 admin@XorPlus# commit Commit OK. Save done. admin@XorPlus#
Verify the static route entry in the RIB as follows:
admin@XorPlus# run show route static RIB entry for static ==================== Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP, F - PBR, f - OpenFabric, > - selected route, * - FIB route, q - queued route, r - rejected route S>* 10.10.2.0/24 [1/0] via 10.10.6.1, vlan-4, weight 1, 00:40:35 S>* 0.0.0.0/0 [1/0] via 10.10.3.1, vlan-3, weight 1, 05:00:04
Configuring Switch B
Configure 3 VLAN interfaces for networks 10.10.2.1/24, 10.10.4.1/24, and 10.10.6.2/24. Then, configure a static route to 10.10.1.0/24 and a default route.
admin@XorPlus# set vlans vlan-id 2 admin@XorPlus# set vlans vlan-id 3 admin@XorPlus# set vlans vlan-id 4 admin@XorPlus# set interface gigabit-ethernet ge-1/1/1 family ethernet-switching native-vlan-id 2 admin@XorPlus# set interface gigabit-ethernet ge-1/1/2 family ethernet-switching native-vlan-id 3 admin@XorPlus# set interface gigabit-ethernet ge-1/1/3 family ethernet-switching native-vlan-id 4 admin@XorPlus# set vlans vlan-id 2 l3-interface vlan-2 admin@XorPlus# set vlans vlan-id 3 l3-interface vlan-3 admin@XorPlus# set vlans vlan-id 4 l3-interface vlan-4 admin@XorPlus# commit Commit OK. Save done. admin@XorPlus# set l3-interface vlan-interface vlan-2 address 10.10.2.1 prefix-length 24 admin@XorPlus# set l3-interface vlan-interface vlan-3 address 10.10.4.1 prefix-length 24 admin@XorPlus# set l3-interface vlan-interface vlan-4 address 10.10.6.1 prefix-length 24 admin@XorPlus# set ip routing enable true admin@XorPlus# set protocols static route 10.10.1.0/24 next-hop 10.10.6.1 admin@XorPlus# set protocols static route 0.0.0.0/0 next-hop 10.10.4.2 admin@XorPlus# commit Commit OK. Save done. admin@XorPlus#
Verify the static route entry in the RIB:
admin@XorPlus# run show route static RIB entry for static ==================== Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP, F - PBR, f - OpenFabric, > - selected route, * - FIB route, q - queued route, r - rejected route S>* 10.10.1.0/24 [1/0] via 10.10.6.1, vlan-4, weight 1, 00:40:35 S>* 0.0.0.0/0 [1/0] via 10.10.4.1, vlan-3, weight 1, 05:00:04
Configuring Switch C
Configure 3 VLAN interfaces for networks 10.10.3.2/24, 10.10.4.2/24, and 10.10.5.2/24. Then, configure a static route to 10.10.1.0/24 and a default route.
admin@XorPlus# set vlans vlan-id 2 admin@XorPlus# set vlans vlan-id 3 admin@XorPlus# set vlans vlan-id 4 admin@XorPlus# set interface gigabit-ethernet ge-1/1/1 family ethernet-switching native-vlan-id 2 admin@XorPlus# set interface gigabit-ethernet ge-1/1/2 family ethernet-switching native-vlan-id 3 admin@XorPlus# set interface gigabit-ethernet ge-1/1/3 family ethernet-switching native-vlan-id 4 admin@XorPlus# set vlans vlan-id 2 l3-interface vlan-2 admin@XorPlus# set vlans vlan-id 3 l3-interface vlan-3 admin@XorPlus# set vlans vlan-id 4 l3-interface vlan-4 admin@XorPlus# commit Commit OK. Save done. admin@XorPlus# set l3-interface vlan-interface vlan-2 address 10.10.3.2 prefix-length 24 admin@XorPlus# set l3-interface vlan-interface vlan-3 address 10.10.4.2 prefix-length 24 admin@XorPlus# set l3-interface vlan-interface vlan-4 address 10.10.5.2 prefix-length 24 admin@XorPlus# set ip routing enable true admin@XorPlus# set protocols static route 10.10.1.0/24 next-hop 10.10.3.1 admin@XorPlus# set protocols static route 10.10.2.0/24 next-hop 10.10.4.1 admin@XorPlus# set protocols static route 10.10.6.0/24 next-hop 10.10.3.1 admin@XorPlus# set protocols static route 0.0.0.0/0 next-hop 10.10.5.1 admin@XorPlus# commit Commit OK. Save done. admin@XorPlus#
Verify the static route entry in the RIB:
admin@XorPlus# run show route static RIB entry for static ==================== Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP, F - PBR, f - OpenFabric, > - selected route, * - FIB route, q - queued route, r - rejected route S>* 10.10.1.0/24 [1/0] via 10.10.3.2, vlan-2, weight 1, 00:40:35 S>* 10.10.2.0/24 [1/0] via 10.10.4.2, vlan-3, weight 1, 00:40:35 S>* 10.10.6.0/24 [1/0] via 10.10.3.2, vlan-2, weight 1, 00:40:35 S>* 0.0.0.0/0 [1/0] via 10.10.5.2, vlan-4, weight 1, 05:00:04
Copyright © 2024 Pica8 Inc. All Rights Reserved.