Installing PICOS on Bare Metal Switches
- Tracy Yang
Introduction
When using ONIE installer to install PICOS, the installer reinstalls the software, rebuilds all the PICOS file system. This can erase the configuration files and system logs from the previous installation.
After a successful ONIE installation of PICOS 4.x, the system generates multiple system partitions including PicOS (partition size: 2G), PicOS2 (partition size: 2G) and User-Data partitions. Among them, PicOS and PicOS2 are two independent system boot partitions. One of them is the active partition on which the running system resides, and the other is the inactive partition. The two-system-boot-partition feature allows the system to revert to a previous version of the installed software package when the it fails to upgrade PICOS by using upgrade2 command.
The ONIE installer removes all partitions to rebuild a brand new OS only when there is no User-Data partition. However, if there exists a User-Data partition (for example, install a new version 4.0.1 from the old one 4.0.0), the ONIE installer only rewrites the "PicOS" partition, installs the new installation package to this partition and sets the system on "PicOS" partition as the default and sole boot system.
User-Data partition is a reserved partition which is not affected by ONIE installer and upgrade unless user manually removes it. User-Data partition uses all the available space left on the disk. Users can use this partition to store files and data.
This document describes how to install PICOS 4.x software using ONIE installer.
Installation Notes and Tools
The installation methods used to install a new PICOS are traditional installation and nos-boot-mode installation. You can choose a suitable installation method that is convenient and appropriate for your installation environment.
- If you want to install the PICOS through a non-console port (through the management port), refer to section 18972698.
• You need to log in through the console port of the switch and perform the ONIE installation.
• Other NOSes including user data will be removed when install PICOS under ONIE environment.
• When the ONIE installer is used to downgrade the PICOS version from version 4.x to PICOS 3.x or lower versions, we first need to use ONIE to uninstall the higher version PICOS before proceeding with installing PICOS 3.x or a lower version. On the ARM platform, execute the onie_uninstaller command at the ONIE prompt to uninstall the current version PICOS. On the x86 platform, select the "ONIE: Uninstall OS" option in the GRUB menu to uninstall the current version PICOS.
• If you enter GRUB rescue mode and the switch has GPT format partition, you can use the following commands to reset the GRUB boot variable to enter ONIE GRUB and then install PICOS.
grub rescue> set prefix=(hd0,gpt2)/grub
grub rescue> set root=(hd0,gpt2)
grub rescue> insmod normal
grub rescue> normal
• Do not plug in the USB disk during onie-nos-installer process until ONIE starts up. If you have plugged in the USB disk before the installation operation, ONIE will find the installer on the USB disk when beginning the installation. On AS4610 series switches, when installation is complete, the installer will display: Please take out the usb disc, then remove the USB disk within 10 seconds after installation successful, and before machine restarts.
• All X86 platforms share one installation and upgrade package with the name fixed as: onie-installer-picos-VERSION-x86.bin, where VERSION is the release version. X86 platform are listed below:
• FS N5850-48S6Q
• FS N8550-48B8C
• FS N8550-32C
• FS N8560-64C
• FS N8550-24CD8D
• Edgecore AS4630-54PE
• Edgecore AS5712-54X
• Edgecore AS5812-54T
• Edgecore AS5812-54X
• Edgecore AS7312-54X
• Edgecore AS7326-56X
• Edgecore AS7712-32X
• Edgecore AS7726-32X
• Edgecore AS7816-64X
• Edgecore AS5835-54X
• Edgecore AS9716-32D
• DELL N3248P-ON
• DELL N3248PXE-ON
• DELL N3224PX-ON
• DELL N3248X-ON
• DELL S4048-ON
• DELL S4148F-ON
• DELL S4148T-ON
• DELL S4128F-ON
• DELL S5224F-ON
• DELL S5296F-ON
• DELL S5212F-ON
• DELL S5248F-ON
• DELL Z9100-ON
• DELL Z9264F-ON
• DELL N3224T-ON
• DELL S4128T-ON
What is ONIE
ONIE (Open Network Install Environment) is an open source project of OCP (Open Compute Project). ONIE provides the environment to install any network operating system on a bare metal network switch. ONIE liberates users from captive pre-installed network operating systems, like the Cisco IOS, and provides them with a choice.
ONIE is a small Linux operating system that comes pre-installed as firmware on bare metal network switches. ONIE acts as an enhanced boot loader, extending the features provided by U-Boot. ONIE is used to install Pica8 PICOS on compatible switches. The bare metal switches listed in the PICOS Hardware Compatibility List must be pre-loaded with ONIE prior to installing PICOS.
Traditional Installation
NOTE：
|
Mind Map of Installation Process
Figure1 shows the mind map of PICOS installation process.
Figure1 Mind Map of PICOS installation process
Manual Installation Process
The following example describes the installation of PICOS via manual installation method.
Step1
Make sure that the installation package of .bin file has been load to the server (server could be HTTP, TFTP, or an FTP server or the switch local directory depending on the actual installation environment).
Step2 Enter ONIE installation environment. The process is different on the following two types of platforms:
- ARM Platforms (AS4610 Series Switches)
a)
Verify that the switch is pre-loaded with ONIE, which will be used to load PICOS on the switch. Power on the switch and interrupt the boot sequence by pressing any key when the following line is shown:
Hit any key to stop autoboot:
b)
User will then reach the U-Boot command prompt indicated by ->. Run the printenv command at the U-Boot prompt. If the information displayed contains keywords like onie_initargs and onie_machine, the switch is pre-loaded with ONIE.
LOADER->printenv
active=image1
autoload=no
baudrate=115200
bootcmd=run check_boot_reason;run PicOS_bootcmd;run onie_bootcmd
bootdelay=10
check_boot_reason=if test -n $onie_boot_reason; then setenv onie_bootargs boot_reason=$onie_boot_reason; run onie_bootcmd; fi;
consoledev=ttyS0
dhcp_user-class=arm-accton_as4610_54-r0_uboot
dhcp_vendor-class-identifier=arm-accton_as4610_54-r0
ethact=eth-0
ethaddr=00:18:23:30:E7:8F
fdtaddr=0xc00000
fpboot=setenv bootargs console=${consoledev},${baudrate} maxcpus=2 mem=1024M root=/dev/ram ${mtdparts} ubi.mtd=4 ethaddr=$ethaddr quiet
gatewayip=192.168.0.1
initrd_high=0x80000000
ipaddr=192.168.0.1
loadaddr=0x70000000
loads_echo=1
mfg=mfg
mfgdiags=run fpboot ; nand read ${loadaddr} diags ; bootm ${loadaddr}
mfgdiags_recovery=nand read ${loadaddr} diags2 ; nand erase.part diags ; nand write ${loadaddr} diags
mtdids=nand0=nand_iproc.0
mtdparts=mtdparts=nand_iproc.0:1m(uboot),2m(shmoo),1m(nenv),12m(onie),3992m(open),12m(onie2),2m(vpd),6m(sys_eeprom),16m(diags),16m(diags2),32m(diags_fs)
netmask=255.255.255.0
nos_bootcmd=true
onie_args=run onie_initargs onie_platformargs
onie_bootcmd=echo Loading Open Network Install Environment ...; echo Platform: $onie_platform ; echo Version : $onie_version ; nand read $loadaddr $onie_start 0x00c00000 && run onie_args && bootm ${loadaddr}
onie_dropbear_dss_host_key=begin-base64@600@d#AAAAB3NzaC1kc3MAAACBAIN7HOS7UGtQ+RS9R5Rdim9s4iadCBQ9SEFnHJZ2#ulK15hN2p1BOJ1Mf4qb/oHFGIt8hvopq157ejsJcSPuR9scXE2aYQO7r1+Ie#1MKoR3HyEFKgPhNUr0qYNiIaWGw2UUXivLUlhjmaPhjItsttb6AezNB6N1ap#TmIeEUse0NQBAAAAFQDndwbRrSsw6G/W4wd0LJVAjuyq2QAAAIAe/zGPyPNn#UwwV+i+j3l1W9IFhjA/ovXfX7PQtjHB7OJcInSpOA2gXLXHU2kYDkn+ymJQI#8Tn558nLHq64n9hIJzwaQH4ajMipBNwqR0WtpPXEaow9InDzjs+qFY0HAcTv#7DMEY9BGiJAUUSSCSFZ9dEYHIWUdk6WIpDUMX4b2ewAAAIB6bC+fHzr+Qaet#GjzynI0tApbzyydXKuIiIH6EDh2QEaP0E+TSxJ+C4xfyBAp1j0kvj0IYWR2P#H9ur0RaxDaCmKwIQs1gTJh/137Yd+OsqEV3JnrZxlEKk2DmI5c2wrGtl4oUp#XJfc+viahpFeCsGzsqGHHADWNsjlpKt457QCuQAAABUAk5406cTH4nZO0qlj#6irYf4WA65E=#====#
onie_dropbear_rsa_host_key=begin-base64@600@r#AAAAB3NzaC1yc2EAAAADAQABAAAAgQCMTqwNhnJpuSLYAdRA/jjm1lyBaJF1#ovs3Hp0G7XkYnY4+JNPTCYgnmfMQnM83PQncuy89AqehJ2V22LGjpRiqT56K#MRr+hQoSWEbAObRd1azZF45pbxiQaQiQxNzIKbHDDWlGlycXfv8w9ZCElbxj#Ja7bkwmwg9EsBlW0d5u0BQAAAIAFr0FOyfn0OR1FiatvF624Aorcbl9oV/pc#JRghGfl8SxPihizz4bC7xAPCUkwd9ZHi+M2E6AjhIV69xjFKS0vYuQplvl8G#9R8YsnmP5B45TyLE3dW5V2/g+LQERQdFpRaSsPqEPHSlXPq4XHLGLRFItEBt#ohp41Qm+eA6efsAMIQAAAEEA4Y90xi8N1SuwjRk53fqpP8dC+FPnU850XtC1#cKG0rBt6v9qD+BTxxfE6GEpYM+N0fLyECbgBjA2LQF6CG3G15QAAAEEAnz3v#3POrcsMK2LkSNjWzAhzUqOWyOaNlhcvgh+2Xfj2tHyOTpZ09gCm483v1rui9#63uYu4QQurpATrHMcLIjoQ==#====#
onie_initargs=setenv bootargs quiet console=$consoledev,$baudrate
onie_machine=accton_as4610_54
onie_machine_rev=0
onie_platform=arm-accton_as4610_54-r0
onie_platformargs=setenv bootargs $bootargs serial_num=${serial#} ${platformargs} eth_addr=$ethaddr $onie_bootargs $onie_debugargs
onie_recovery=nand read ${loadaddr} onie2 ; nand erase.part onie ; nand write ${loadaddr} onie
onie_rescue=setenv onie_boot_reason rescue && boot
onie_start=onie
onie_sz.b=0x00c00000
onie_uninstall=setenv onie_boot_reason uninstall && boot
onie_update=setenv onie_boot_reason update && boot
onie_vendor_id=27658
onie_version=master-201603091701-dirty
PicOS_bootcmd=usb start;run platformargs;setenv bootargs root=/dev/sda1 rw noinitrd console=$consoledev,$baudrate rootdelay=10 $mtdparts;ext2load usb 0:1 $loadaddr boot/uImage;bootm $loadaddr
platform=accton_as4610_54
platformargs=mtdparts=nand_iproc.0:1m(uboot),2m(shmoo),1m(nenv),12m(onie),3992m(open),12m(onie2),2m(vpd),6m(sys_eeprom),16m(diags),16m(diags2),32m(diags_fs) maxcpus=2 mem=1024M
ramdiskaddr=0x3000000
serial#=A626P1DL174300014
serverip=192.168.0.10
stderr=serial
stdin=serial
stdout=serial
ubifscfg=ubi part nand0,4 0x0; ubifsmount fs
ver=U-Boot 2012.10-gcbef171 (Mar 09 2016 - 17:01:14) - ONIE master-201603091701-dirty
Environment size: 3992/65532 bytes
c) From U-Boot prompt, boot ONIE in rescue mode.
LOADER-> run onie_rescue
- x86 Platform
On x86 platform, it uses GRUB menu to install OS via ONIE.
a) Reboot the system, and enter ONIE installation environment from the GRUB menu:
+----------------------------------------------------------------------------+
| PicOS |
|*ONIE |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
+----------------------------------------------------------------------------+
Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, `e' to edit the commands
before booting or `c' for a command-line.
b) From GRUB prompt, choose ONIE: Rescue to Install OS, boot ONIE in rescue mode.
GNU GRUB version 2.02~beta2+e4a1fe391 +----------------------------------------------------------------------------+ |*ONIE: Install OS | | ONIE: Rescue | | ONIE: Uninstall OS | | ONIE: Update ONIE | | ONIE: Embed ONIE | | DIAG: Accton Diagnostic | | | | | | | | | | | | | +----------------------------------------------------------------------------+
Step3 Run onie-nos-install command as follows to manually install PICOS.
- Install via TFTP
ONIE# onie-nos-install tftp://<path to image>/PICOS.bin
- Install via FTP
When installing via FTP, you need to type username and password of the FTP server on which the image file is loaded.
ONIE# onie-nos-install ftp://username:password@<path to image>/PICOS.bin
- Install via HTTP
ONIE# onie-nos-install http://<path to image>/PICOS.bin
- Install from Local Directory
a) In ONIE rescue mode, copy the image file to the current directory.
ONIE# scp username@<path to image>/PICOS.bin .
b) Run onie-nos-install command to start installation.
ONIE# onie-nos-install PICOS.bin
For example,
ONIE:/ # onie-nos-install onie-installer-picos-4.0.0-8b1219e112-x86.bin discover: Rescue mode detected. No discover stopped. ONIE: Executing installer: onie-installer-picos-4.0.0-8b1219e112-x86.bin Verifying image checksum ... OK. Preparing image archive ... OK. [1] PICOS L2/L3 (default) [2] PICOS Open vSwitch/OpenFlow Enter your choice (1,2):1 PICOS L2/L3 is selected. ONIE installation will overwrite the configuration file of existing system. It is recommended to follow the upgrade procedure to upgrade the system. Press any key to stop the installation... 10 9 8 7 6 5 4 3 2 1 ...
The installer runs automatically, before start installation, it will prompt to choose the option to make PICOS to boot into L2/L3 or OVS mode. If not selected, then PICOS boots into L2/L3.
After finishing installation, the device reboots automatically, the system then comes up running the new network operating system.
NOTE：
|
Automatic Installation Process
The automatic installation process uses the DHCP message exchange process to download and install software packages.
Step1 Make sure the switch is connected to DHCP and HTTP servers and the PICOS installation software package is downloaded to the HTTP server.
a) DHCP server configuration: define the path of the installation package and then start DHCP server service:
host pica8-3922 {
hardware ethernet 70:72:cf:12:34:56;
fixed-address 192.168.2.50;
option default-url = "http://192.168.2.42/onie-installer-picos-4.0.0-8b1219e112-x86.bin";
}
b) Check if the .bin installation file is loaded onto the HTTP server:
root@dev:/var/www# ls index.html onie-installer-powerpc.bin
Step2 Install PICOS via ONIE. The process is different on the following two types of platforms:
- ARM Platforms (AS4610 Series Switches)
a)
Verify that the switch is pre-loaded with ONIE, which will be used to load PICOS on the switch. Power on the switch and interrupt the boot sequence by pressing any key when the following line is shown:
Hit any key to stop autoboot:
b)
User will then reach the U-Boot command prompt indicated by ->. Run the printenv command at the U-Boot prompt. If the information displayed contains keywords like onie_initargs and onie_machine, the switch is pre-loaded with ONIE.
LOADER-> printenv
active=image1
autoload=no
baudrate=115200
bootcmd=run check_boot_reason;run PicOS_bootcmd;run onie_bootcmd
bootdelay=10
check_boot_reason=if test -n $onie_boot_reason; then setenv onie_bootargs boot_reason=$onie_boot_reason; run onie_bootcmd; fi;
consoledev=ttyS0
dhcp_user-class=arm-accton_as4610_54-r0_uboot
dhcp_vendor-class-identifier=arm-accton_as4610_54-r0
ethact=eth-0
ethaddr=00:18:23:30:E7:8F
fdtaddr=0xc00000
fpboot=setenv bootargs console=${consoledev},${baudrate} maxcpus=2 mem=1024M root=/dev/ram ${mtdparts} ubi.mtd=4 ethaddr=$ethaddr quiet
gatewayip=192.168.0.1
initrd_high=0x80000000
ipaddr=192.168.0.1
loadaddr=0x70000000
loads_echo=1
mfg=mfg
mfgdiags=run fpboot ; nand read ${loadaddr} diags ; bootm ${loadaddr}
mfgdiags_recovery=nand read ${loadaddr} diags2 ; nand erase.part diags ; nand write ${loadaddr} diags
mtdids=nand0=nand_iproc.0
mtdparts=mtdparts=nand_iproc.0:1m(uboot),2m(shmoo),1m(nenv),12m(onie),3992m(open),12m(onie2),2m(vpd),6m(sys_eeprom),16m(diags),16m(diags2),32m(diags_fs)
netmask=255.255.255.0
nos_bootcmd=true
onie_args=run onie_initargs onie_platformargs
onie_bootcmd=echo Loading Open Network Install Environment ...; echo Platform: $onie_platform ; echo Version : $onie_version ; nand read $loadaddr $onie_start 0x00c00000 && run onie_args && bootm ${loadaddr}
onie_dropbear_dss_host_key=begin-base64@600@d#AAAAB3NzaC1kc3MAAACBAIN7HOS7UGtQ+RS9R5Rdim9s4iadCBQ9SEFnHJZ2#ulK15hN2p1BOJ1Mf4qb/oHFGIt8hvopq157ejsJcSPuR9scXE2aYQO7r1+Ie#1MKoR3HyEFKgPhNUr0qYNiIaWGw2UUXivLUlhjmaPhjItsttb6AezNB6N1ap#TmIeEUse0NQBAAAAFQDndwbRrSsw6G/W4wd0LJVAjuyq2QAAAIAe/zGPyPNn#UwwV+i+j3l1W9IFhjA/ovXfX7PQtjHB7OJcInSpOA2gXLXHU2kYDkn+ymJQI#8Tn558nLHq64n9hIJzwaQH4ajMipBNwqR0WtpPXEaow9InDzjs+qFY0HAcTv#7DMEY9BGiJAUUSSCSFZ9dEYHIWUdk6WIpDUMX4b2ewAAAIB6bC+fHzr+Qaet#GjzynI0tApbzyydXKuIiIH6EDh2QEaP0E+TSxJ+C4xfyBAp1j0kvj0IYWR2P#H9ur0RaxDaCmKwIQs1gTJh/137Yd+OsqEV3JnrZxlEKk2DmI5c2wrGtl4oUp#XJfc+viahpFeCsGzsqGHHADWNsjlpKt457QCuQAAABUAk5406cTH4nZO0qlj#6irYf4WA65E=#====#
onie_dropbear_rsa_host_key=begin-base64@600@r#AAAAB3NzaC1yc2EAAAADAQABAAAAgQCMTqwNhnJpuSLYAdRA/jjm1lyBaJF1#ovs3Hp0G7XkYnY4+JNPTCYgnmfMQnM83PQncuy89AqehJ2V22LGjpRiqT56K#MRr+hQoSWEbAObRd1azZF45pbxiQaQiQxNzIKbHDDWlGlycXfv8w9ZCElbxj#Ja7bkwmwg9EsBlW0d5u0BQAAAIAFr0FOyfn0OR1FiatvF624Aorcbl9oV/pc#JRghGfl8SxPihizz4bC7xAPCUkwd9ZHi+M2E6AjhIV69xjFKS0vYuQplvl8G#9R8YsnmP5B45TyLE3dW5V2/g+LQERQdFpRaSsPqEPHSlXPq4XHLGLRFItEBt#ohp41Qm+eA6efsAMIQAAAEEA4Y90xi8N1SuwjRk53fqpP8dC+FPnU850XtC1#cKG0rBt6v9qD+BTxxfE6GEpYM+N0fLyECbgBjA2LQF6CG3G15QAAAEEAnz3v#3POrcsMK2LkSNjWzAhzUqOWyOaNlhcvgh+2Xfj2tHyOTpZ09gCm483v1rui9#63uYu4QQurpATrHMcLIjoQ==#====#
onie_initargs=setenv bootargs quiet console=$consoledev,$baudrate
onie_machine=accton_as4610_54
onie_machine_rev=0
onie_platform=arm-accton_as4610_54-r0
onie_platformargs=setenv bootargs $bootargs serial_num=${serial#} ${platformargs} eth_addr=$ethaddr $onie_bootargs $onie_debugargs
onie_recovery=nand read ${loadaddr} onie2 ; nand erase.part onie ; nand write ${loadaddr} onie
onie_rescue=setenv onie_boot_reason rescue && boot
onie_start=onie
onie_sz.b=0x00c00000
onie_uninstall=setenv onie_boot_reason uninstall && boot
onie_update=setenv onie_boot_reason update && boot
onie_vendor_id=27658
onie_version=master-201603091701-dirty
PicOS_bootcmd=usb start;run platformargs;setenv bootargs root=/dev/sda1 rw noinitrd console=$consoledev,$baudrate rootdelay=10 $mtdparts;ext2load usb 0:1 $loadaddr boot/uImage;bootm $loadaddr
platform=accton_as4610_54
platformargs=mtdparts=nand_iproc.0:1m(uboot),2m(shmoo),1m(nenv),12m(onie),3992m(open),12m(onie2),2m(vpd),6m(sys_eeprom),16m(diags),16m(diags2),32m(diags_fs) maxcpus=2 mem=1024M
ramdiskaddr=0x3000000
serial#=A626P1DL174300014
serverip=192.168.0.10
stderr=serial
stdin=serial
stdout=serial
ubifscfg=ubi part nand0,4 0x0; ubifsmount fs
ver=U-Boot 2012.10-gcbef171 (Mar 09 2016 - 17:01:14) - ONIE master-201603091701-dirty
Environment size: 3992/65532 bytes
c) Input command run onie_bootcmd, which will automatically install PICOS on the switch.
LOADER -> run onie_bootcmd Loading Open Network Install Environment ... Platform: arm-accton_as4610_54-r0 Version : 2021.09.00.03 WARNING: adjusting available memory to 30000000 ## Booting kernel from Legacy Image at 02000000 ... Image Name: as4610_54x.1.6.1.3 Image Type: ARM Linux Multi-File Image (gzip compressed) Data Size: 3514311 Bytes = 3.4 MiB Load Address: 00000000 Entry Point: 00000000 Contents: Image 0: 2762367 Bytes = 2.6 MiB Image 1: 733576 Bytes = 716.4 KiB Image 2: 18351 Bytes = 17.9 KiB Verifying Checksum ... OK ## Loading init Ramdisk from multi component Legacy Image at 02000000 ... ## Flattened Device Tree from multi component Image at 02000000 Booting using the fdt at 0x02355858 Uncompressing Multi-File Image ... OK Loading Ramdisk to 2ff4c000, end 2ffff188 ... OK Loading Device Tree to 03ff8000, end 03fff7ae ... OK Cannot reserve gpages without hugetlb enabled setup_arch: bootmem as4610_54x_setup_arch() arch: exit pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01) sd 0:0:0:0: [sda] No Caching mode page present sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] No Caching mode page present sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] No Caching mode page present sd 0:0:0:0: [sda] Assuming drive cache: write through ONIE: Using DHCPv4 addr: eth0: 192.168.2.77 / 255.255.255.0 discover: installer mode detected. Running installer. Please press Enter to activate this console. ONIE: Using DHCPv4 addr: eth0: 192.168.2.77 / 255.255.255.0 ONIE: Starting ONIE Service Discovery ONIE: Executing installer: http://192.168.2.42/onie-installer-picos-4.0.0-8b1219e112-x86.bin Verifying image checksum ... OK. Preparing image archive ... OK. PicOS installation .............................................. ./var/local/ ./var/run Setup PicOS environment ... .............................................. XorPlus login: admin Password: You are required to change your password immediately (root enforced) Changing password for admin. (current) UNIX password: Enter new UNIX password: Retype new UNIX password: admin@XorPlus$
- x86 Platform
On x86 platform, it uses GRUB menu to choose install OS via ONIE.
a) Reboot the system, and enter ONIE installation environment from the GRUB menu:
+----------------------------------------------------------------------------+
| PicOS |
|*ONIE |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
+----------------------------------------------------------------------------+
Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, `e' to edit the commands
before booting or `c' for a command-line.
b) From GRUB prompt, choose ONIE: Rescue to Install OS, boot ONIE in rescue mode.
GNU GRUB version 2.02~beta2+e4a1fe391 +----------------------------------------------------------------------------+ |*ONIE: Install OS | | ONIE: Rescue | | ONIE: Uninstall OS | | ONIE: Update ONIE | | ONIE: Embed ONIE | | DIAG: Accton Diagnostic | | | | | | | | | | | | | +----------------------------------------------------------------------------+
The installer runs and will reboot the system after installation is complete.
NOTE：
|
Nos-boot-mode Installation
NOTE：
|
The installation methods described in 18972698 must be performed through the console port. If you want to install the system through a non-console port, you can use the nos-boot-mode command to perform the installation which is described in this section.
Usage of nos-boot-mode command: admin@Xorplus$sudo nos-boot-mode USAGE install or uninstall NOS(es) SYNOPSIS nos-boot-mode [install|uninstall] DESCRIPTION install- Install NOS uninstall- Remove all NOS(es) including PICOS When nos-boot-mode install command is executed, PICOS will switch to ONIE install mode, and the user should go on to complete the subsequent installation. The steps for the manual installation process and the automatic installation process using the nos-boot-mode install command are described below. When nos-boot-mode unsinstall command is executed, the system will remove all NOS(es) including PICOS from the device. Therefore, it is suggested to use the nos-boot-mode unsinstall command with caution. |
Manual Installation Process
Step1 Make sure that the installation package of .bin file has been loaded to the server (server could be HTTP, TFTP, or an FTP server or the switch local directory depending on the actual installation environment).
Step2 Execute the nos-boot-mode install command to enter ONIE installation environment.
admin@Xorplus:~$ sudo nos-boot-mode install
Step3 Type “yes” when the below prompt is shown, which will take the system will to ONIE install mode.
Type 'yes' to install NOS! Type 'no' to exit [no]/yes:
Step4 Run onie-nos-install command as follows to manually install PICOS.
- Install via TFTP
ONIE# onie-nos-install tftp://<path to image>/PICOS.bin
- Install via FTP
When installing via FTP, you need to type in the username and password for the FTP server on which the image file is loaded.
ONIE# onie-nos-install ftp://username:password@<path to image>/PICOS.bin
- Install via HTTP
ONIE# onie-nos-install http://<path to image>/PICOS.bin
- Install from Local Directory
a) In ONIE rescue mode, copy the image file to the current directory.
ONIE# scp username@<path to image>/PICOS.bin .
b) Run onie-nos-install command to start installation.
ONIE# onie-nos-install PICOS.bin
For example,
ONIE:/ # onie-nos-install onie-installer-picos-4.0.0-8b1219e112-x86.bin discover: Rescue mode detected. No discover stopped. ONIE: Executing installer: onie-installer-picos-4.0.0-8b1219e112-x86.bin Verifying image checksum ... OK. Preparing image archive ... OK. [1] PICOS L2/L3 (default) [2] PICOS Open vSwitch/OpenFlow Enter your choice (1,2):1 PICOS L2/L3 is selected. ONIE installation will overwrite the configuration file of existing system. It is recommended to follow the upgrade procedure to upgrade the system. Press any key to stop the installation... 10 9 8 7 6 5 4 3 2 1 ...
The installer runs automatically, before start installation, it will prompt to choose the option to make PICOS to boot into L2/L3 or OVS mode. If not selected, then PICOS boots into L2/L3.
After finishing installation, the device reboots automatically, the system then comes up running the new network operating system.
NOTE：
|
Automated Installation Process
The automatic installation process uses the DHCP message exchange process to download and install software packages.
Step1 Make sure the switch is connected to DHCP and HTTP servers, and the PICOS installation software package is downloaded to the HTTP server.
a) DHCP server configuration: define the path of the installation package and then start DHCP server service:
host pica8-3922 {
hardware ethernet 70:72:cf:12:34:56;
fixed-address 192.168.2.50;
option default-url = "http://192.168.2.42/onie-installer-picos-4.0.0-8b1219e112-x86.bin";
}
b) Check if the .bin installation file is loaded onto the HTTP server:
root@dev:/var/www# ls index.html onie-installer-powerpc.bin
Step2 Execute the nos-boot-mode install command to enter ONIE installation environment.
admin@Xorplus$ sudo nos-boot-mode install
Step3 Type “yes” when the below prompt is shown, and the system will automatically complete the installation.
Type 'yes' to install NOS! Type 'no' to exit [no]/yes:
The installer runs automatically and will reboot the system after installation is completed.
NOTE：
|
Verifying Version after Installation
After system reboots automatically, the system will come up running the new network operating system.
admin@Xorplus> show version Copyright (C) 2009-2022 Pica8, Inc. =================================== Hardware Model : as7312_54x Linux System Version/Revision : 4.0.0/8b1219e112 Linux System Released Date : 5/18/2021 L2/L3 Version/Revision : 4.0.0/8b1219e112 L2/L3 Released Date : 5/18/2021 OVS/OF Version/Revision : 4.0.0/8b1219e112 OVS/OF Released Date : 5/18/2021
Appendix: Troubleshooting Installation/Upgrade Failure on AS7326-56X
Installation or upgrade failure (for example, the switches cannot boot up after install) may occur on the old AS7326-56X hardware models (revision is R01F and before). When booting PICOS on AS7326-56X and detect hardware rev R01F, the system will log a warning message to prompt the hardware revision R01F is a pre-production hardware reversion: "This hardware revision R01F is a pre-production hardware rev, PICOS has applied a work around to work with PICOS. Support will be provided on a best effort basis".
To work around the issue, first we need to check the “Label Revision”. If it is an old hardware model (revision is R01F or before), then, we can perform the following provided solution after installation/upgrade to solve the problem.
Check Label Revision
Under ONIE prompt, run “onie_syseeprom” to get the “Label Revision”.
ONIE:/ # onie-syseeprom TlvInfo Header: Id String: TlvInfo Version: 1 Total Length: 166 TLV Name Code Len Value -------------------- ---- --- ----- Manufacture Date 0x25 19 04/27/2019 02:10:06 Label Revision 0x27 4 R01B Platform Name 0x28 27 x86_64-accton_as7326_56x-r0 ONIE Version 0x29 13 2018.05.00.05 Manufacturer 0x2B 6 Accton Diag Version 0x2E 7 0.0.1.0 Base MAC Address 0x24 6 80:A2:35:81:D5:F0 Serial Number 0x23 14 732656X1916012 Country Code 0x2C 2 TW Part Number 0x22 13 FP4ZZ7656005A Product Name 0x21 15 7326-56X-O-AC-F MAC Addresses 0x2A 2 256 Vendor Name 0x2D 6 Accton CRC-32 0xFE 4 0xC3D3F2DE Checksum is valid. ONIE:/ #
Solution
You can follow the steps below after installation/upgrade, to fix the problem of installation and upgrade failure on the old AS7326-56X hardware model (revision R01F or before).
Step1 Power cycle the switch.
Step2 From the GRUB menu, choose “ONIE” to enter ONIE GRUB menu:
+----------------------------------------------------------------------------+
| PicOS |
|*ONIE |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
+----------------------------------------------------------------------------+
Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, `e' to edit the commands
before booting or `c' for a command-line.
Step3 From ONIE GRUB menu, choose “ONIE: Rescue” to launch ONIE in Rescue mode.
GNU GRUB version 2.02~beta2+e4a1fe391 +----------------------------------------------------------------------------+ | ONIE: Install OS | |*ONIE: Rescue | | ONIE: Uninstall OS | | ONIE: Update ONIE | | ONIE: Embed ONIE | | DIAG: Accton Diagnostic | | | | | | | | | | | | | +----------------------------------------------------------------------------+
Step4 Press Enter to display the ONIE prompt.
Step5 Mount PicOS partition with label is “PicOS”.
ONIE:/ # blkid /dev/sda7: LABEL="User-Data" UUID="be63cef8-4560-4c48-ab5a-8f7ced5a950b" /dev/sda6: LABEL="PicOS2" UUID="f589e53f-4cd1-44ba-8384-f339f4e2b2ac" /dev/sda5: LABEL="PicOS" UUID="8ca5f7ed-5a15-4a2a-944c-4d8872647bf5" /dev/sda4: LABEL="PICOS-GRUB" UUID="782a1372-4b66-4783-b920-dab1df8ec6e4" /dev/sda3: LABEL="ACCTON-DIAG" UUID="3e4117d0-1926-472a-9d9e-08883df83d40" /dev/sda2: LABEL="ONIE-BOOT" UUID="1a90abd8-f065-4f7a-90a0-af122b8805fa" ONIE:/ # ONIE:/ # mount /dev/sda5 /mnt
Step6 Execute the following command to modify the I2C access address.
ONIE:/ # sed -I "s/0x57/0x56/" /mnt/etc/rc_hw.sh ONIE:/ # sync
Step7 Unmount the PicOS partition.
ONIE:/ # unmount /dev/sda5
Step8 Reboot the switch.
ONIE:/ # reboot
Copyright © 2024 Pica8 Inc. All Rights Reserved.