QoS Configuration Commands

This section contains descriptions of the Layer2 and Layer3 QoS configuration commands that this chapter references.

• class-of-service classifier <classifier-name>
• class-of-service classifier <classifier-name> forwarding-class <forwarding-class-name> code-point <code-point>
• class-of-service classifier <classifier-name> trust-mode <trust-mode>
• class-of-service forwarding-class <forwarding-class-name> local-priority <local-priority>
• class-of-service interface <port> classifier <classifier-name>
• class-of-service scheduler <scheduler-name> guaranteed-rate <guaranteed-rate>
• class-of-service scheduler <scheduler-name> mode SP
• class-of-service scheduler <scheduler-name> mode WFQ
• class-of-service scheduler <scheduler-name> mode WRR
• class-of-service scheduler <scheduler-name> weight <weight-id>
• class-of-service scheduler-profile <scheduler-profile-name> forwarding-class <forwarding-class-name> schedule <schedule-name>
• show class-of-service <text>
• set class-of-service interface scheduler-profile
• class-of-service interface <port> default-priority <default-priority-type> <default-priority-int>
• class-of-service pfc-profile <profile-name> code-point <code-point> drop <boolean>
• class-of-service interface <port> pfc-profile <profile-name>
• set firewall filter sequence then dscp
• set class-of-service scheduler max-rate
• CoPP Commands
  • set class-of-service forwarding-class local-priority
  • set class-of-service scheduler max-bandwidth-pps
  • set class-of-service scheduler min-bandwidth-pps
  • set class-of-service scheduler-profile copp-profile forwarding-classs scheduler
  • set class-of-service scheduler weight
  • set firewall filter copp sequence from destination-address-ipv4
  • set firewall filter copp sequence from destination-address-ipv6
  • set firewall filter copp sequence from destination-mac-address
  • set firewall filter copp sequence from destination-port
  • set firewall filter copp sequence from ether-type
  • set firewall filter copp sequence from protocol
  • set firewall filter copp sequence from source-address-ipv4
  • set firewall filter copp sequence from source-address-ipv6
  • set firewall filter copp sequence from source-mac-address
  • set firewall filter copp sequence from source-port
  • set firewall filter copp sequence from vlan
  • set firewall filter copp sequence then forwarding-class
  • set firewall filter copp sequence then dscp
  • run show copp bandwidth
  • run show copp statistics
  • run show filter copp
  • run show interface stm
  • run clear copp statistics
• Buffer Management Commands
  • set interface ethernet-switching-options buffer egress-queue shared-ratio
  • set interface ethernet-switching-options buffer egress-queue mc-queue-dynamic-shared
  • run show gigabit-ethernet egress-queues
  • run show interface egress-buffer
• Interface-based Rate Limiting Commands
  • set interface gigabit-ethernet rate-limiting ingress kilobits
  • set interface gigabit-ethernet rate-limiting ingress ratio
  • set interface gigabit-ethernet rate-limiting ingress burst
  • set interface gigabit-ethernet rate-limiting egress kilobits
  • set interface gigabit-ethernet rate-limiting egress ratio
  • set interface gigabit-ethernet rate-limiting egress burst
• ACL-based Traffic Policer Commands
  • set firewall policer if-exceeding count-mode
  • set firewall policer if-exceeding rate-limit
  • set firewall policer if-exceeding burst-limit
  • set firewall policer if-exceeding action discard
  • set firewall filter sequence then policer
  • run show policer
• PFC Watchdog
  • set class-of-service pfc-watchdog granularity
  • set class-of-service pfc-watchdog restore-action
  • set class-of-service pfc-watchdog code-point detect-interval
  • set class-of-service pfc-watchdog code-point restore-interval
  • set class-of-service interface pfc-watchdog code-point enable
  • run show pfc-watchdog config
  • run show pfc-watchdog stats