PICOS Documentation
Spaces
Apps
Templates
Create
PICOS-4.4.4_Configuration_Guide (Special Release)
All content
Space settings
Content
Results will update as you type.
•
Release Notes for PICOS 4.4.4 (Special Release)
Hardware Guides
PICOS System Configuration Guide
PICOS Routing and Switching Configuration Guide
PICOS Routing and Switching Command Reference
Command-Line Interface Commands
System Management Commands
VLAN Configuration Commands
Layer 3 Routing Commands
Voice VLAN Configuration Commands
ACL Configuration Commands
QoS Configuration Commands
Protocol Configuration Commands
IP Multicast Commands
•
OpenFlow Commands in CrossFlow Mode
VXLAN Commands
BGP EVPN Commands
PoE Configuration Commands
VRRP Commands
Spanning Tree Protocol Commands
MLAG Commands
GRE Tunnel Interface Commands
GVRP Commands
MVRP Commands
ERPS Commands
EFM OAM Commands
Interface Configuration Commands
Port Security Commands
L3 Interface
Routed Interface
Uplink Failure Detection Commands
•
run show interface ufd
•
set interface ufd link-to-monitor
•
set interface ufd link-to-disable
IPv6 Neighbor Discovery Protocol Command Reference
•
set management-ethernet-speed eth0
•
set interface gigabit-ethernet up-mode
•
set interface gigabit-ethernet speed
•
show interface bpdu-tunneling
•
show interface aggregate-ethernet <lag_name>
•
show interface aggregate-ethernet <lag_name> dot1q-tunneling
•
show interface brief
•
show interface detail
•
show interface diagnostics optics all
•
show interface ecmp max-path
•
show interface flexlink
•
show interface gigabit-ethernet <interface>
•
set interface gigabit-ethernet fec
•
set interface gigabit-ethernet family ethernet-switching vlan members
•
set interface gigabit-ethernet family ethernet-switching port-mode
•
set interface gigabit-ethernet family ethernet-switching bpdu-tunneling protocol
•
set interface gigabit-ethernet ether-options 802.3ad
•
set interface gigabit-ethernet duplex auto
•
set interface gigabit-ethernet cdr
•
set interface gigabit-ethernet breakout
•
set interface gigabit-ethernet auto-speeds
•
set interface ecmp hash-mapping field vlan disable
•
set interface ecmp hash-mapping field port-source disable
•
set interface ecmp hash-mapping field port-destination disable
•
set interface ecmp hash-mapping field ip-source disable
•
set interface ecmp hash-mapping field ip-protocol disable
•
set interface ecmp hash-mapping field ip-destination disable
•
set interface ecmp hash-mapping field ingress-interface disable
•
set interface bpdu-tunneling destination-mac
•
set interface aggregate-ethernet family ethernet-switching vlan members
•
set interface aggregate-ethernet family ethernet-switching port-mode
•
set interface aggregate-ethernet disable
•
set interface aggregate-ethernet description
•
set interface aggregate-ethernet aggregated-ether-options lacp fallback timeout
•
set interface aggregate-ethernet aggregated-ether-options lacp fallback enable
•
set interface aggregate-ethernet aggregated-ether-options lacp
•
set interface aggregate-ethernet
•
run show interface port-index-mapping
•
run show interface diagnostics tdr
•
interface max-route-limit
•
interface max-acl-rule-limit <egress/ingress>
•
interface gigabit-ethernet <port> wred queue <value> min_thresh
•
interface gigabit-ethernet <port> wred queue <value> max_thresh
•
interface gigabit-ethernet <port> wred queue <value> enable
•
interface gigabit-ethernet <port> wred queue <value> ecn_thresh
•
interface gigabit-ethernet <port> wred queue <value> drop_probability
•
interface gigabit-ethernet <port> storm-control <mode> ratio <value>
•
interface gigabit-ethernet <port> storm-control <mode> pps
•
interface gigabit-ethernet <port> storm-control <mode> kbps
•
interface gigabit-ethernet <port> static-ethernet-switching mac-address <mac-address> vlan <vlan-id>
•
interface gigabit-ethernet <port> snmp-trap
•
interface gigabit-ethernet <port> power-preemphasis-level
•
interface gigabit-ethernet <port> mtu
•
interface gigabit-ethernet <port> mac-learning <boolean>
•
interface gigabit-ethernet <port> link-fault-signaling ignore-remote-fault <boolean>
•
interface gigabit-ethernet <port> link-fault-signaling ignore-local-fault <boolean>
•
interface gigabit-ethernet <port> family ethernet-switching vlan members <vlan-id> untagged
•
interface gigabit-ethernet <port> family ethernet-switching native-vlan-id
•
interface gigabit-ethernet <port> family ethernet-switching dot1q-tunneling mode
•
interface gigabit-ethernet <port> family ethernet-switching dot1q-tunneling ingress
•
interface gigabit-ethernet <port> family ethernet-switching dot1q-tunneling ether-type
•
interface gigabit-ethernet <port> family ethernet-switching dot1q-tunneling egress
•
interface gigabit-ethernet <port> disable
•
interface gigabit-ethernet <port> ether-options flow-control
•
interface gigabit-ethernet <port> description
•
interface gigabit-ethernet <port> crossflow local-control
•
interface gigabit-ethernet <port> crossflow enable
•
interface gigabit-ethernet <port> backup-port mode
•
interface gigabit-ethernet <port> backup-port interface
•
interface gigabit-ethernet <port> backup-port delay
•
interface ethernet-switching-options mac-table-aging-time
•
interface ethernet-switching-options buffer queue-limit
•
interface ecmp max-path
•
interface cut-through-mode
•
interface aggregate-ethernet <lag_name> storm-control <mode> pps
•
interface aggregate-ethernet <lag_name> static-ethernet-switching mac-address <macaddr> vlan
Show more below
Blogs
You‘re viewing this with anonymous access, so some content might be blocked.
Close
PICOS-4.4.4_Configuration_Guide (Special Release)
/
Uplink Failure Detection Commands
Uplink Failure Detection Commands
Tracy Yang
Owned by
Tracy Yang
May 24, 2024
Loading data...
run show interface ufd
set interface ufd link-to-monitor
set interface ufd link-to-disable
Copyright © 2025 Pica8 Inc. All Rights Reserved.
{"serverDuration": 13, "requestCorrelationId": "b70c605f2e184d74994e76408073fdc1"}