/
QoS Configuration Commands
QoS Configuration Commands
This section contains descriptions of the Layer2 and Layer3 QoS configuration commands that this chapter references.
- set class-of-service forwarding-class local-priority
- set class-of-service scheduler mode
- set class-of-service interface default-priority
- set class-of-service classifier forwarding-class code-point
- set class-of-service interface classifier
- set class-of-service classifier
- set class-of–service classifier forwarding-class
- set class-of-service classifier trust-mode
- set class-of-service scheduler guaranteed-rate
- set class-of-service scheduler-profile forwarding-class scheduler
- set class-of-service scheduler weight
- set class-of-service easy-ecn mode
- set class-of-service interface scheduler-profile
- set class-of-service scheduler max-rate
- run show class-of-service interface
- CoPP Commands
- set class-of-service scheduler max-bandwidth-pps
- set class-of-service scheduler min-bandwidth-pps
- set class-of-service scheduler-profile copp-profile forwarding-classs scheduler
- set class-of-service scheduler weight (CoPP)
- set firewall filter copp sequence from destination-address-ipv4
- set firewall filter copp sequence from destination-address-ipv6
- set firewall filter copp sequence from destination-mac-address
- set firewall filter copp sequence from destination-port
- set firewall filter copp sequence from ether-type
- set firewall filter copp sequence from protocol
- set firewall filter copp sequence from source-address-ipv4
- set firewall filter copp sequence from source-address-ipv6
- set firewall filter copp sequence from source-mac-address
- set firewall filter copp sequence from source-port
- set firewall filter copp sequence from vlan
- set firewall filter copp sequence then forwarding-class
- set firewall filter copp sequence then dscp
- run show copp bandwidth
- run show copp statistics
- run show interface stm
- run clear copp statistics
- set class-of-service forwarding-class local-priority (CoPP)
- run show filter copp
- Buffer Management Commands
- Interface-based Rate Limiting Commands
- set interface gigabit-ethernet rate-limiting ingress kilobits
- set interface gigabit-ethernet rate-limiting ingress ratio
- set interface gigabit-ethernet rate-limiting ingress burst
- set interface gigabit-ethernet rate-limiting egress kilobits
- set interface gigabit-ethernet rate-limiting egress ratio
- set interface gigabit-ethernet rate-limiting egress burst
- ACL-based Traffic Policer Commands
- PFC Commands
- set class-of-service pfc-profile code-point drop
- set class-of-service interface pfc-profile
- set interface gigabit-ethernet ethernet-switching-options buffer ingress-queue guaranteed
- set interface gigabit-ethernet ethernet-switching-options buffer ingress-queue shared-ratio
- set interface gigabit-ethernet ethernet-switching-options buffer ingress-queue threshold
- set interface gigabit-ethernet ethernet-switching-options buffer ingress-queue reset-offset
- set interface ethernet-switching-options buffer service-pool threshold
- set interface gigabit-ethernet ethernet-switching-options buffer ingress-queue headroom
- set interface gigabit-ethernet ethernet-switching-options buffer egress-queue shared-ratio
- set interface gigabit-ethernet ethernet-switching-options buffer egress-queue threshold
- set class-of-service pfc-watchdog granularity
- set class-of-service pfc-watchdog restore-action
- set class-of-service pfc-watchdog code-point detect-interval
- set class-of-service pfc-watchdog code-point restore-interval
- set class-of-service interface pfc-watchdog code-point enable
- set class-of-service pfc-watchdog threshold period
- set class-of-service pfc-watchdog threshold count
- set class-of-service interface pfc-watchdog restore-mode
- run clear class-of-service interface pfc-watchdog auto
- run clear class-of-service interface pfc-watchdog manual
- run show pfc-watchdog stats
- run show pfc-watchdog config
- run show interface gigabit-ethernet ingress-buffer
- run show interface gigabit-ethernet egress-buffer
- set class-of-service interface pfc-uplink-group
- set class-of-service pfc-uplink-group original-dscp to-code-point
- set class-of-service pfc-uplink-group original-dscp dscp
, multiple selections available,
Related content
CoPP Commands
CoPP Commands
More like this
CoPP Commands
CoPP Commands
More like this
CoPP Commands
CoPP Commands
More like this
Configuring Easy ECN
Configuring Easy ECN
Read with this
Configuring Dynamic Load Balancing
Configuring Dynamic Load Balancing
Read with this
Copyright © 2025 Pica8 Inc. All Rights Reserved.