/

PICOS Routing and Switching Command Reference

PICOS Routing and Switching Command Reference

Owned by Tracy Yang (Unlicensed)

Mar 16, 2021

Command-Line Interface Commands

System Management Commands

Interface Configuration Commands

Voice VLAN Configuration Commands

Firewall Configuration Commands

QoS Configuration Commands

class-of-service classifier <classifier-name>
class-of-service classifier <classifier-name> forwarding-class <forwarding-class-name> code-point <code-point>
class-of-service classifier <classifier-name> trust-mode <trust-mode>
class-of-service forwarding-class <forwarding-class-name> local-priority <local-priority>
class-of-service interface <port> classifier <classifier-name>
class-of-service scheduler <scheduler-name> guaranteed-rate <guaranteed-rate>
class-of-service scheduler <scheduler-name> mode SP
class-of-service scheduler <scheduler-name> mode WFQ
class-of-service scheduler <scheduler-name> mode WRR
class-of-service scheduler <scheduler-name> weight <weight-id>
class-of-service scheduler-profile <scheduler-profile-name> forwarding-class <forwarding-class-name> schedule <schedule-name>
show class-of-service <text>
set class-of-service interface scheduler-profile
class-of-service interface <port> default-priority <default-priority-type> <default-priority-int>
class-of-service pfc-profile <profile-name> code-point <code-point> drop <boolean>
class-of-service interface <port> pfc-profile <profile-name>
set firewall filter sequence then dscp
set class-of-service scheduler max-rate
CoPP Commands
- set class-of-service forwarding-class local-priority
- set class-of-service scheduler max-bandwidth-pps
- set class-of-service scheduler min-bandwidth-pps
- set class-of-service scheduler-profile copp-profile forwarding-classs scheduler
- set class-of-service scheduler weight
- set firewall filter copp sequence from destination-address-ipv4
- set firewall filter copp sequence from destination-address-ipv6
- set firewall filter copp sequence from destination-mac-address
- set firewall filter copp sequence from destination-port
- set firewall filter copp sequence from ether-type
- set firewall filter copp sequence from protocol
- set firewall filter copp sequence from source-address-ipv4
- set firewall filter copp sequence from source-address-ipv6
- set firewall filter copp sequence from source-mac-address
- set firewall filter copp sequence from source-port
- set firewall filter copp sequence from vlan
- set firewall filter copp sequence then forwarding-class
- set firewall filter copp sequence then dscp
- run show copp bandwidth
- run show copp statistics
- run show filter copp
- run show interface stm
- run clear copp statistics
Buffer Management Commands
- set interface ethernet-switching-options buffer egress-queue shared-ratio
- set interface ethernet-switching-options buffer egress-queue mc-queue-dynamic-shared
- run show gigabit-ethernet egress-queues
- run show interface egress-buffer
Interface-based Rate Limiting Commands
- set interface gigabit-ethernet rate-limiting ingress kilobits
- set interface gigabit-ethernet rate-limiting ingress ratio
- set interface gigabit-ethernet rate-limiting ingress burst
- set interface gigabit-ethernet rate-limiting egress kilobits
- set interface gigabit-ethernet rate-limiting egress ratio
- set interface gigabit-ethernet rate-limiting egress burst
ACL-based Traffic Policer Commands
- set firewall policer if-exceeding count-mode
- set firewall policer if-exceeding rate-limit
- set firewall policer if-exceeding burst-limit
- set firewall filter sequence then policer
- set firewall policer if-exceeding action discard
- run show policer

Layer 3 Unicast Routing Commands

IP Multicast Commands

Protocol Configuration Commands

OpenFlow Commands in CrossFlow Mode

VLAN Configuration Commands

VXLAN Commands

PoE Configuration Commands

VRRP Commands

Spanning Tree Protocol Commands

MLAG Commands

Copyright © 2025 Pica8 Inc. All Rights Reserved.